Full Metal Jacket Paint Protection 30ml (1 fl oz)- the world's most durable and highest performing paint protection, designed for automotive applications.Superhydrophic, Oleophobic and yielding a hardness of 8 Mohs whilst retaining flexibility for automotive applications.
Full Metal Jacket Paint Protection, originally produced in 2002 for sealing paint, was updated in 2006 to seal glass, chrome, bare plastics (such as ABS), wheels, tail and headlights (glass, acrylic or polycarbonate) polyurethane (stone chip protection films) and vinyl (such as sticker and livery).
In 2008, Full Metal Jacket Paint Protection was updated again, becoming the the world's first superhydrophobic coating for matte surfaces, adjusting gloss levels by less than 1gu.
Full Metal Jacket, now in its third iteration provides protection for ALL exterior surfaces on all vehicles.
Full Metal Jacket Paint Protection inhibits 99% of UV rays from penetrating the coating for its life. Maintained correctly (as recommended here), a layer of Full Metal Jacket will last 2-5 years depending on the amount and type of use of the vehicle, maintenance (washing), weathering (garaging helps significantly), amount of UV the coating is subjected to and the consistency and quality of Full Metal Jacket Spray Wax maintenance layers.
Most daily driven vehicles will enjoy 2 years of performance from a single unlayered coat of Full Metal Jacket Paint Protection with a quality, regular (weekly) maintenance regime.
Full Metal Jacket is a professional product, it is a very high quality product that can be applied by anyone in three simple steps, but it does have professional application characteristics.
Final Inspection detailers HIGHLY recommend you carefully read and understand the directions at least once before application.
You may also want to have handy (or purchase) the products mentioned below for optimising preparation. Preparation is 99% of the end result and it vital to maximising the performance of your coating.
Wear the gloves any time you are applying the product or handling the cloths you have used for the coating. The solvent in the product is aggressive and can cause irritation to skin. Always use any car care product chemicals in an environment with adequate ventilation.
Full Metal Jacket is a professional product, the product is of a very high quality and as such the skill level required for application is low.
However, as a professional product, careful attention and respect for the application directions are absolutely necessary. Full Metal Jacket cures, literally, as hard as concrete, so removal of incorrect application is difficult and labour intensive.
It is ABSOLUTELY NECESSARY to apply Full Metal Jacket to a clean car. It is also HIGHLY recommended to decontaminate paint prior to Full Metal Jacket to allow for better adhesion, a cleanse with Paint Cleanse is highly recommended. Paint Cleanse removes oils that will hinder the adhesion of Full Metal Jacket to the Paint Surface. Do not use Cleanse or any other Decontamination products & methods when layering Full Metal Jacket to maintain the coating, Paint Cleanse will strip the coating so it is only used to prepare for the coating, not to maintain it.
Always use Paint Cleanse with Clean NanoFibre Paintwork Cloths only.
Add about 5ml (10-12 drops) of Full Metal Jacket to a NanoFibre Hand Pocket Applicator. This amount will only be require the first section, it is the amount required to prime the applicator.
Apply to each area with straight back & forth motions, slightly overlapping each stroke for complete coverage.
Thinner layers are better so you may want to vary the amount of product you are applying to the applicator, but not too thin, even coverage is vital. Apply Full Metal Jacket to one one small section at a time, we recommend a maximum area of about 1 x 1 foot, break large panels, such as bonnets and roofs into three to four smaller sections. DO NOT APPLY FULL METAL JACKET TO THE ENTIRE VEHICLE.
Full Metal Jacket has an instant bond, so removal of the excess is required instantly, DO NOT ALLOW THE COATING TO DRY.
There is no need to agitate the product on the surface, no circular motions are necessary as the coating does not have any polishing characteristics.
After applying, remove the excess IMMEDIATELY with a Dry NanoFibre Paintwork Cloth.
Turn the cloth over frequently and buff the surface until you are absolutely sure all excess is removed. You cannot accidentally remove all the coating, so don't worry about over-buffing. It is vital to remove all the excess to avoid any smearing, approximately 1um of the coating transfers and bonds instantly and cannot be removed with dry buffing, this is the layer of polymers you are attempting to transfer, your sacrificial layer of protection.
Repeat the process in step 1 and 2 until all Paintwork is treated, remember to work only small sections at any one time, do not try to rush the application by working large areas HOWEVER, re-apply only 1-2ml (2-4 drops) of FMJ to the applicator this time and from now on.
In some conditions and after 1/2 hour curing, smearing or hazing may be present, Remove the smearing with a clean damp MicroFibre Paintwork Cloth followed by a Dry Paintwork Cloth. Do not use a previously used cloth as the loading of excess product in the cloth can reapply some Full Metal Jacket and cause smearing.
CHARACTERISTICS / APPEARANCE
Full Metal Jacket has incredible Washing Characteristics. FMJ is super-hydrophobic with high surface tension and this will be visually demonstrated very clearly during maintenance of the vehicle. When these characteristics are not as prominent, it is time to re-apply protection. With normal use of the vehicle (20,000km per year), Full Metal Jacket should exhibit its protective characteristics for a minimum of 1 year and up to 5 years depending on your washing regime, type of use and maintenance with a layering sealant such as Full Metal Jacket Spray Wax.
Full Metal Jacket beads water extremely well. The beads of water quickly join on the slightest panel angle or with light wind to form larger beads that use their weight to move off the hydrophobic surface. Beads become less perky towards the end of the Full Metal Jacket life and signal the end of the Full Metal Jacket ’s protective properties. Full Metal Jacket is Ultra Slick, especially when rejuvenated with FMJ Spray Wax. Spray Wax maintains your Full Metal Jacket layer better than any other product and better than waxes as it contains small amounts of the high quality polymers that bond to the Full Metal Jacket layer.
Full Metal Jacket provides a sacrificial layer above your clear coat to block & absorb damage from weathering. Full Metal Jacket is usually 1 micron thick when applied correctly. The layer resists abrasion however aggressive (incorrect) maintenance (washing) will still mark your painted surface. If the layer is damaged by aggressive chemicals such as those in bird droppings, it will need to be replaced, but Full Metal Jacket will either prevent or greatly reduce the damage that the chemicals in bird droppings will cause to your paint as a result of contact with the surface. Full Metal Jacket has been lab tested and protects very well against UV. This will almost completely prevent paintwork coated with Full Metal Jacket against oxidising. White cars don’t turn chalky and Red cars don’t turn pink!
One coat of Full Metal Jacket typically provides for 18-24 months of protection depending on how the vehicle is used and maintained. Durability can be increased by layering Full Metal Jacket with Spray Wax(after the curing period). The longevity of the layer of Full Metal Jacket depends on many factors, 2 Major factors are: Washing with pH neutral soaps are HIGHLY recommended, this reduces aggressive deterioration of the protective layer of polymer Full Metal Jacket. Garaging, reducing weathering will increase Full Metal Jacket life and reduce washing intervals.
You MUST make sure you carry out the application with ALL the safety measures we've outlined as Full Metal Jacket is a chemical and your safety is of the upmost importance. Professionals can become complacent with the materials they use and we want to remind you that you are using Chemicals and Safety & Care when using these products must always be your highest priority.
Bonding Time is the time a Full Metal Jacket requires to adhere to a surface before you can remove the excess product by buffing. Full Metal Jacket version 4 now requires zero bonding time. You must remove the excess instantly.
Curing is the time Full Metal Jacket must be allowed to rest to gather full strength. During the Curing Time do not wash or apply waxes to the coating.
Full Metal Jacket has a Curing Time of 72 hours although 7 days is HIGHLY RECOMMENDED. After curing DO NOT use Cleansers, Clay or any other Decontamination products & methods as they will remove some or all of your FMJ layer of protection. Do not layer Full Metal Jacket with itself, Full Metal Jacket does not layer over itself efficiently, the solvents in FMJ remove most of itself so it doesn't build layers well, it is unnecessary, but reapplication every 2-5 years, is.
The best way to build layers is to use Full Metal Jacket Spray Wax for maintenance. You can layer Full Metal Jacket with a Pure Wax. Pure Waxes are waxes containing no solvents to clean surfaces as they are applied. Solvents in waxes 'clean away' any underlying waxes or Full Metal Jacket, so aren't useful for layering. Dedicated or Pure Waxes & Full Metal Jacket are the only types of Waxes & Full Metal Jacket recommended for use.
Enjoy easier maintenance of your painted surface with your Full Metal Jacket Paint Protection!